|
|
|
|
|
|
|
|
|
|
|
|
|
|
#8 split lock washer
|
# 6 split lock washer
|
#10 split lock washer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#12 split lock washer
|
8-32 X 5/16 " Fillister head slotted screw . Common use is throttle plate screws on single barrel DLTX carburetors, they also fit our new Ensign throttle shafts and have other uses. Order lockwasher separately, part 8LW
|
6-32 X 1/4 " Fillister head slotted screw . Common use is choke plate screws on single barrel DLTX carburetors, they also fit our new Ensign choke shafts and have other uses. Order lockwasher separately, part 6LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#4 X 1/4" SEMS Pan head slotted screw with internal tooth lock washer
|
#6 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
10-32 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on Zenith 61 , 161 , 67 , 68 and some other carburetors. Order lockwasher separately, part 10LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10-24 X 5/8" Fillister head slotted screw . Common use is Farmall cub bowl to body screws and some other carburetors. Order lockwasher separately, part 10LW
|
#4 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
12-24 X 3/4" Fillister head slotted screw . Common use is the throttle body to bowl screws on medium and large ( 1-3/16" , 1-5/16" & 1-7/16" throttle bore diameter) TSX carburetors, and Zenith 267 series. Order lockwasher separately, part 12LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12-24 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on small ( 1-1/16" & 1-1/8" throttle bore diameter) TSX carburetors. Also generally the length installed on 267 Zenith although book specifies 3/4". Order lockwasher separately, part 12LW
|
#5-40 X 1/4" SEMS Pan head slotted screw with split lock washer. Typically used as throttle and choke disk screws on thousands of Zenith , some Marvel Schebler carburetors, and others.
|
#5-40 X 5/16-3/8" long. Exact length and material may vary with stock on hand. Oval head machine screw Use on IH Farmall carburetor throttle shafts and most Zenith with tapered hole shaft.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
carburetor flange mounting gasket will fit 1 13/16 " center to center mounting holes for 1/4" bolts and a 15/16" center hole used with IH cub 251235R1 some Wisconsin's and anything else with these measurements
|
Carburetor float bowl works on most Carter N with "flat bottom" type bowl . Some Carter N used a dish/dome type bowl and this will not work on those. There are also some bowls that look the same but have a 5/16" bottom hole and this will not work on those either. Also fits some Briggs replacing 221995 and some Kohler. Rough dimensions are 2-5/16" diameter with 3/8" bottom hole and 1-1/4" height . Check dimensions before ordering.
|
|
|
