|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dual nozzle plug, H nut, flt. val. gasket
|
Can be used on the strainer bolt of 1 bbl DLTX and Ensign strainer cage nut
|
Ensign strainer cage igloo gasket also fits John Deere 530 630 730 2 barrel DLTX carburetors when equipped with vent chamber gasket roughly 1.625" X 1.328" X 1/16" replaces F3248R
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ensign BJ and K Idle or BJ Load needle spring
|
Ensign K load needle valve spring
|
Ensign choke friction spring
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 bolt Carburetor mounting gasket for 10-20 International Ensign carburertor for 2 bolt mountings look at C141-4-280
|
Ensign choke plate for International IHC 10-20, Regular, and others . Roughly 1.200" diameter .We made these out of stainless steel, hopefully you'll never have to replace it again.
|
Drain cock
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ensign hardware kit . Includes bowl to body screws and lock washers . Includes new choke screw friction assembly ( replaces C1149R spring, C1148R spacer/sleeve, C1145R / C1146R washers ) . This choke friction assembly is slightly different than original design but looks and works fine.
|
1/8" NPT Drain cock with internal seal, highly recommend this for the DLTX 3 and is a great replacement on the International Farmall carburetors if you don't want to pay for OEM style. This valve handle actually screws away, instead of toward the carb, so it works well in some particular applications.
|
Ensign carburetor filter strainer screen. Flat screen measures roughly 1/2" ID X 1-3/8" OD and fits most Ensign carburetors including but not limited to ones used on John Deere GP, International 10-20 , Regular, Hart Parr, KGN carbs Etc basically any that measurement is close. Pushes into fuel inlet cage.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ensign strainer cage nut
|
1/4" NPT Drain cock with internal seal, highly recommend this for the Zenith K5. This valve handle actually screws away, instead of toward the carb, so it works well in some particular applications.
|
Ensign R carburetor gaskets for International IHC 10-20, Regular, etc, Some gaskets may work on other sizes possibly
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ensign float pin screw
|
Ensign choke shaft
|
Ensign choke disk
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ensign throttle plate for International IHC 10-20, Regular, and others of that diameter.
|
Ensign K idle adjusting screw
|
Ensign K throttle shaft
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Throttle bushing for Ensign BJ DX304 and DLTX 3 carburetors used on John Deere GP and D. Attaches to throttle shaft with a 15-181(R10036) set screw. Machine work may be necessary to install.
|
Throttle disk Ensign BJ
|
Throttle disk Ensign K
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ensign BJ throttle shaft
|
Ensign K load needle valve
|
Ensign Float valve/needle and seat
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ensign suction stem for IHC 10-20, Regular, and others
|
Ensign BJ load adjusting screw
|
Ensign BJ idle adjusting screw
|
|
|
