|
|
|
|
|
|
|
|
|
|
|
|
|
|
#8 split lock washer
|
# 6 split lock washer
|
#10 split lock washer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#12 split lock washer
|
8-32 X 5/16 " Fillister head slotted screw . Common use is throttle plate screws on single barrel DLTX carburetors, they also fit our new Ensign throttle shafts and have other uses. Order lockwasher separately, part 8LW
|
6-32 X 1/4 " Fillister head slotted screw . Common use is choke plate screws on single barrel DLTX carburetors, they also fit our new Ensign choke shafts and have other uses. Order lockwasher separately, part 6LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#4 X 1/4" SEMS Pan head slotted screw with internal tooth lock washer
|
#6 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
10-32 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on Zenith 61 , 161 , 67 , 68 and some other carburetors. Order lockwasher separately, part 10LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10-24 X 5/8" Fillister head slotted screw . Common use is Farmall cub bowl to body screws and some other carburetors. Order lockwasher separately, part 10LW
|
#4 X 1/4" SEMS Pan head slotted screw with external tooth lock washer
|
12-24 X 3/4" Fillister head slotted screw . Common use is the throttle body to bowl screws on medium and large ( 1-3/16" , 1-5/16" & 1-7/16" throttle bore diameter) TSX carburetors, and Zenith 267 series. Order lockwasher separately, part 12LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#5-40 X 1/4" SEMS Pan head slotted screw with split lock washer. Typically used as throttle and choke disk screws on thousands of Zenith , some Marvel Schebler carburetors, and others.
|
#5-40 X 5/16-3/8" long. Exact length and material may vary with stock on hand. Oval head machine screw Use on IH Farmall carburetor throttle shafts and most Zenith with tapered hole shaft.
|
12-24 X 5/8" Fillister head slotted screw . Common use is the throttle body to bowl screws on small ( 1-1/16" & 1-1/8" throttle bore diameter) TSX carburetors. Also generally the length installed on 267 Zenith although book specifies 3/4". Order lockwasher separately, part 12LW
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
carburetor flange mounting gasket will fit 1 13/16 " center to center mounting holes for 1/4" bolts and a 15/16" center hole used with IH cub 251235R1 some Wisconsin's and anything else with these measurements
|
carburetor flange mounting gasket oblong mounting holes will fit most 2 1/4 , 2 5/16 and 2 3/8 center to center with 1/4" or 5/16" mounting bolts
|
Knurled brass throttle bushing for 1/4" shaft. Presses into 5/16" hole. 1/2" in length. May need to be shortened depending on the application.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
throttle bushing for 5/16" shaft. Presses into 3/8" hole. 3/8" in length. Replaces Marvel Schebler 60-260 used from the factory in some 1-7/16" throttle bore TSX carburetor
|
Knurled brass throttle bushing for 5/16" shaft. Presses into 3/8" hole. 1/2" in length. May need to be shortened depending on the application. C9-56
|
Stromburg UC body bowl split gasket only. Fits Wisconsin ADH AEH AFH AGH AHH VE-4 VF-4 and carb #'s 425000A / 001A / 17 / 18 / 41 / 44 / 93 / 94 , 426013 / 15 / 19 / 20 / 21 / 26 / 39 / 40 / 41 / 64 / 67 / 73 / 80 , and 427014. Wisconsin #'s L-45- (2 9 11 14 20 22 A A-1 A-2 A-4 B B-2 B-3 E E-3 E-4 E-6 E-8 F-1 J K)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
porous bronze carburetor drip hole plug 1/8 NPT . This threaded fitting can be used on any carburetor with 1/8" NPT threads for the throat drip hole
|
porous bronze carburetor drip hole plug 1/4 NPT . This threaded fitting can be used on any carburetor with 1/4" NPT threads for the throat drip hole
|
Zenith 61 161 67 68 float valve (needle & seat) also fits Stromberg UC carburetor
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
fuel strainer screen to repair most 1/8" NPT fittings. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.215" outside diameter
|
fuel strainer screen to repair most IH fuel fittings such as H M Supers, 300 460 etc. Must be soldered or glued in with fuel resistant material into fitting. Measures approximately 0.312" outside diameter
|
Zenith 62 63 69 267 float valve needle and seat replaces C81-68-40 Can also be substituted for C81-1 C81-3 C81-20 and 81-39 type valves
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Drain cock
|
Zenith carburetor float valve needle and seat fits K5 and others replaces C81-20-50 D6560 can generally be used on most of the 124 1/2 series
|
1/8" NPT Drain cock with internal seal, highly recommend this for the DLTX 3 and is a great replacement on the International Farmall carburetors if you don't want to pay for OEM style. This valve handle actually screws away, instead of toward the carb, so it works well in some particular applications.
|
|
|
